- How many roof tiles can be laid in a day?
- How do you measure Batten spacing?
- What nails do you use for roof tiles?
- How far apart should purlins be?
- Should roof tiles move in the wind?
- How far apart should roof battens be?
- How many roof tiles do I need calculator?
- How much should Roof Tile overhang?
- How far below roof tiles should Gutter be?
- How far can 2×4 purlins span?
- How often should you nail roof tiles?
- How do you work out Batten gauge for slates?
- Which is stronger Z purlin or C purlin?
- How far can a beam span without support?
- What’s the minimum pitch for slates?
- Are tile roofs nailed down?
- How do you set out roof tile battens?

## How many roof tiles can be laid in a day?

A good roofer should get about 10-12 sq per day…more for the easy roofs and less for difficult ones.

All numbers are based on quality installation at a decent pace..

## How do you measure Batten spacing?

Take your total wall length and divide that by the approximate spacing you would like between the battens. That number will be how many spaces you have on your wall. Add 1 to your number of spaces to get the number of battens on the wall. Now multiply your batten width by the number of battens.

## What nails do you use for roof tiles?

Stainless steel nails are also good for fastening tiles and slate, or you can work with copper nails for standard roofing purposes. Galvanized roofing nails are steel nails that are zinc-coated. They hold up better against rust, and they can also be used for asphalt shingles.

## How far apart should purlins be?

When positioned, roof purlins should be spaced no further than 1.2 metres apart when using sheeting with a thickness of 0.7mm, and 1 metre when using 0.5mm sheeting. Exact requirements will vary, but as a rough guide, this is a good rule of thumb to follow.

## Should roof tiles move in the wind?

Long before the wind force is strong enough to rip the tile off the roof it will be lifted and dropped with each wind gust, making an impact noise, which may result in breakage.

## How far apart should roof battens be?

600mmBattens should be fixed to rafters set at centres not more than 600mm apart. They should span at least three rafters and be at least 1.2m long. No more than one in four battens should be joined over one truss for gauges over 200mm.

## How many roof tiles do I need calculator?

How To Calculate How Many Tiles You Need For Your Roof!A ÷ X = D (Number of Tiles Needed for One Row Across the width)C ÷ Y = E (Number of Rows Needed)D x E = F (Total Number of Tiles Needed for One Side of the Roof)F x 2 = Total Number of Tiles Needed (We Times by Two to Get the Total Number of Tiles Needed for Both Sides of your Roof)

## How much should Roof Tile overhang?

Setting out across the roof Lay a course of tiles along the eaves, setting the tiles at the average linear coverage. At this stage, some adjustment in shunt could be made, if necessary, to allow a 38 to 50mm overhang at verges. Ensure verge overhang is equal at left and right ends.

## How far below roof tiles should Gutter be?

The bottom tile or slate of the roof covering should project at least half way into the gutter – the ideal distance is between half way and two thirds of the way over.

## How far can 2×4 purlins span?

twelve feet2x4 purlins may also be nailed on top of the rafters with one 60-d nail or attached with metal clips at each rafter. Rafters may be spaced up to twelve feet, dependent on purlin size, when purlins are turned edgewise.

## How often should you nail roof tiles?

Every tile of the two rows at the eaves, those up the verges, and along the two rows of the ridge should be nailed, but beyond that it is only necessary to nail every fifth tile horizontally and every third tile as you move up the roof.

## How do you work out Batten gauge for slates?

Batten and Holing Gauges for Natural Slate It also allows you to determine the holing gauge (distance from hole to tail of slate) and the number of linear metres of batten per m2 of roof. Batten gauge = (length of slate-headlap)/2.

## Which is stronger Z purlin or C purlin?

Purlins are horizontal beams that are highly used to support the rafters at roof to increase its life span and to give proper support to roof. … Z Shaped Purlin: This type of z purlins is much stronger than C purlin and often used at joints and overlaps with each other.

## How far can a beam span without support?

When supporting joists that span 12 feet with no overhang beyond the beam, a double ply beam can span in feet a value equal to its depth in inches. A double 2×12 beam can span 12 feet; a (2) 2×10 can span 10 feet and so on.

## What’s the minimum pitch for slates?

Traditionally, a minimum roof pitch of 20° was recommended in BS 5534, but modern tiles and slates have now been designed for applications as low as 15°. It is uncommon to find a roof below 15° but for those very low pitch applications, there are interlocking clay pantiles available, suitable for use down to 12.5°.

## Are tile roofs nailed down?

Nails are the least expensive and most common method for attaching concrete and clay tiles. Tiles can be nailed either directly into the roof sheathing or tiles with lugs can be nailed to battens. … Because of the longevity of a tile roof, some contractors use copper or stainless-steel roofing nails. No.

## How do you set out roof tile battens?

Firstly get two of your roof tiles, and either two full battens or two offcuts of batten and place them onto the roof one above the other. Next place your two tiles, one on top of the other loose onto the battens without anything being fixed. Make sure the tile lugs are seated snuggly onto the top edges of the battens.